Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
We've uncovered the article on Tools You Need to Install a New Bathtub directly below on the net and felt it made good sense to write about it with you in this article.
Installing a bath tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough job. If the old tub is conveniently accessible, the task can relocate quickly; if you have to open up a wall surface to remove the old tub and also position the new tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and also embeded in the brand-new one. Make certain you have qualified on your own for the job and also are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed job, it is far better to consider using one before you start. Possibilities are you might need an expert plumber to make tube links.
This article will help you mount a new bath tub in your washroom if you have actually currently bought a new bathtub as well as do not need to alter the setup of your previous supply of water pipes.
Your devices and material list ought to comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is detach the water supply. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited access that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a towel ready for the remaining water that will certainly come from the pipelines. When the supply pipes have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washing machines are in location between the tap and the sink. Safeguard the faucet in position with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind needs to be connected to the faucet ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the tub in the required position. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the tub up until the spirit level reads level.
To set up taps, fit all-time low of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the water supply and also inspect all joints and new pipework for leakages as well as tighten them if essential. Fill the bath tub and additionally examine the overflow outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as explained in the supplier's user's manual. Tiling as well as securing around the bath tub ought to wait until the tub has actually been used at the very least once as this will certainly resolve it into its last position.
Getting ready for the Installment
To start with, the supporting frame supplied with the bathroom ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to avoid stress on the tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final setting.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to split an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, resulting in difficulties with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the bathtub with water before sealing, to enable the movement experienced when the tub remains in use. The sealant can break rather early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the marketplace. It is advisable to fit the tiles using waterproof or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that post about A Step-by-Step Guide to Installing a Bathtub while doing a search on the internet. Sharing is nice. One never knows, you will be helping someone out. Kudos for your time. Come back soon.
Damage control? Ring! Report this page